Fundamental Plumbing Insights for Installing a Bathtub
Fundamental Plumbing Insights for Installing a Bathtub
Blog Article
Everyone has their own thinking in relation to Installing A Bathtub.
Mounting a bath tub isn't exactly rocket science, yet it does require strong plumbing, woodworking, and often, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably difficult project. If the old tub is easily obtainable, the project can relocate rapidly; if you have to open up a wall to get rid of the old bathtub and also place the new bathtub, the job is much harder. In either case, the task is within a house handyman's abilities, although you will require an assistant to leave the old tub and also set in the new one. Make certain you have actually qualified on your own for the job and also are comfortable trying it. As opposed to working with a professional to take over a halfway-completed job, it is better to consider utilizing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This short article will assist you mount a brand-new tub in your restroom if you have actually already acquired a new tub and also don't require to transform the setup of your previous water pipes.
Your devices and product list should make up the following:
Getting ready for the Setup
First of all, the sustaining frame supplied with the bathroom must be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to prevent stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its final placement.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you should do is separate the water supply. After doing so, switch on the taps to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be rather troublesome as a result of the limited accessibility that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will come from the pipelines. When the supply pipes have been removed, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Prior to proceeding to fit the new taps, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the spirit level and readjusting the feet on the bathtub till the level checks out level.
To mount taps, fit the bottom of the outermost versatile faucet connector to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if needed. Fill the tub as well as additionally examine the overflow electrical outlet as well as the regular electrical outlet for leaks.
Finally, fix the bath paneling as defined in the maker's user's manual. Tiling and also sealing around the bath tub should wait till the bathtub has been utilized at the very least when as this will resolve it right into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making sure that the washers remain in area between the faucet and also the sink. Secure the tap in place with the producer given backnut. Once the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous type needs to be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to crack a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, bring about problems with wetness and also possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components and installations. They are sold in tubes as well as cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can crack rather very early if you do not think about this activity before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent person who reads on Installing A Bathtub, I thought sharing that excerpt was a smart idea. Appreciated our write up? Please share it. Let other people locate it. Kudos for your time. Come back soon.
Visit Website Report this page